DTC guide

P1899 CVT Drive Pulley Pressure Control Solenoid Valve Stuck OFF or CVT Driven Pulley Pressure Control Solenoid Valve Stuck ON

P1899 may indicate a drive pulley pressure control solenoid valve stuck OFF or a driven pulley pressure control solenoid valve stuck ON.

Engine sensors2025 Honda Accord 1.5 turbo

Quick answer

P1899 may indicate a drive pulley pressure control solenoid valve stuck OFF or a driven pulley pressure control solenoid valve stuck ON.

Vehicle coverage: 2025 Honda Accord 1.5 turbo. Confirm the exact configuration and applicable safety procedure before testing or repair.

On this page
  1. What this code means
  2. What the vehicle may do
  3. Possible fault areas
  4. Diagnostic path
  5. What P1899 means
  6. Before troubleshooting
  7. When the TCM stores the code
  8. Valve work item
  9. Separate confirmation procedure
  10. Scanner function
  11. More diagnostic steps
  12. Final check
P1899 CVT Drive Pulley Pressure Control Solenoid Valve Stuck OFF or CVT Driven Pulley Pressure Control Solenoid Valve Stuck ON diagnostic guide

What this code means

P1899 may indicate a drive pulley pressure control solenoid valve stuck OFF or a driven pulley pressure control solenoid valve stuck ON.

The valve name and stuck state must stay paired: OFF applies to the drive pulley valve, while ON applies to the driven pulley valve. The code describes alternatives; it does not by itself identify which valve is affected or establish that both are affected.

What the vehicle may do

  • The TCM may store this code based on pulley and torque conditions.

Possible fault areas

  • The drive pulley pressure control solenoid valve may be stuck OFF.
  • The driven pulley pressure control solenoid valve may be stuck ON.

Diagnostic path

What P1899 means

On your 2025 Honda Accord 1.5, P1899 can mean the CVT Drive Pulley Pressure Control Solenoid Valve is stuck OFF. It can also mean the CVT Driven Pulley Pressure Control Solenoid Valve is stuck ON. Let us walk through the conditions that set this code and the checks for these two valves. Here is what this code tells us. The TCM may store this code based on pulley and torque conditions. Here are the main areas to check. The drive pulley pressure control solenoid valve may be stuck OFF. The driven pulley pressure control solenoid valve may be stuck ON.

Before troubleshooting

Before you troubleshoot, review How to Troubleshoot.

When the TCM stores the code

The TCM stores P1899 when all these conditions apply. The pulley ratio is overdrive while the vehicle is stopped with the forward clutch engaged. The estimated input torque when starting is a specified value or less. Belt slippage does not occur when driving.

These conditions form a combined decision, not three independent reasons to store the code. The stopped-vehicle condition includes both an overdrive pulley ratio and an engaged forward clutch, while the torque condition applies when starting. No belt slippage during driving is also part of that decision, so P1899 should not be read as evidence that the belt is slipping.

Valve work item

For these two valves, the listed work item is replacement of the drive pulley valve and/or the driven pulley valve.

Separate confirmation procedure

Here is the separate confirmation procedure. Raise the vehicle on a lift. Make sure it is securely supported, and allow all four wheels to rotate freely. Start the engine, then disable the VSA. Run the vehicle in D position/mode until the vehicle speed reaches 37 mph (60 km/h). Slow down and stop the wheels. Accelerate from a stop at full throttle in D position/mode. Slow down and stop the wheels. Then turn the vehicle to the OFF (LOCK) mode. Repeat that sequence starting with the engine start: start the engine, then disable the VSA. Run the vehicle in D position/mode until the vehicle speed reaches 37 mph (60 km/h). Slow down and stop the wheels. Accelerate from a stop at full throttle in D position/mode. Slow down and stop the wheels. Then turn the vehicle to the OFF (LOCK) mode.

Scanner function

The diagnostic scanner (HDS) function listed for this code is AT > Data List.

More diagnostic steps

For more diagnostic steps, visit stepdiagnostics.com.

Final check

P1899 may point to either of the two pulley pressure control solenoid valve states.

For more guided automotive diagnostics, visit STEP Diagnostics.