DTC guide

U0131 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-EPS Control Unit)

U0131 can indicate missing or persistently abnormal EPS control unit information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle Network2025 Honda Accord 1.5 turbo

Quick answer

U0131 can indicate missing or persistently abnormal EPS control unit information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle coverage: 2025 Honda Accord 1.5 turbo. Confirm the exact configuration and applicable safety procedure before testing or repair.

On this page
  1. What this code means
  2. What the vehicle may do
  3. Possible fault areas
  4. Diagnostic path
  5. What U0131 means
  6. Before troubleshooting
  7. Identify the affected control unit
  8. Shared confirmation routine
  9. EPS inspection condition
  10. Wiring inspection setup
  11. VF-CAN C_H check
  12. VF-CAN C_L check
  13. What the wiring results mean
  14. U0131 troubleshooting prerequisites
  15. U0131 confirmation routine
  16. Scanner function reference
  17. Final check
U0131 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-EPS Control Unit) diagnostic guide

What this code means

U0131 can indicate missing or persistently abnormal EPS control unit information reaching the PCM through PF-CAN A or PD-CAN B.

What the vehicle may do

  • The PCM may lose the EPS control unit signal.
  • The EPS control unit information may remain abnormal.

Possible fault areas

  • Possible faults include the EPS control unit power/ground circuit.
  • The EPS control unit may not start normally.
  • The CAN circuit or EPS control unit may have a problem.

Diagnostic path

What U0131 means

On this 2025 Honda Accord 1.5, U0131 identifies a PF-CAN A, PD-CAN B malfunction between the Powertrain Control Module (PCM) and EPS Control Unit. The PCM stores this code if it cannot receive the EPS control unit signal through PF-CAN A or PD-CAN B. It also stores the code if information from the EPS control unit stays abnormal continuously for a specified cycle. The code may also be stored if the EPS control unit does not start normally or its power/ground circuit fails. Here is what this code tells us. The PCM may lose the EPS control unit signal. The EPS control unit information may remain abnormal. Here are the main areas to check. Possible faults include the EPS control unit power/ground circuit. The EPS control unit may not start normally. The CAN circuit or EPS control unit may have a problem.

The code describes what the PCM detects, rather than identifying one failed part. Missing EPS communication and continuously abnormal EPS information are separate storage conditions, and EPS startup or power/ground faults can also lead to the code.

Before troubleshooting

Before you troubleshoot, review How to Troubleshoot. If the failure comes and goes or is difficult to reproduce, review How to Troubleshoot (Handling Intermittent and Low Reproducibility Failures). The shared checks address lost communication in the F-CAN circuit connected to the CAN gateway.

Identify the affected control unit

Troubleshoot any DTCs listed or indicated systems below first. - Network Communications \[CAN gateway\]: Go to the indicated DTC's troubleshooting

The diagnostic scanner (HDS) provides Communication Status Check of F-CAN Connected Units. For details on using that function, review How to Troubleshoot (Handling Ongoing Failures). Check the power/ground circuit of the transmitting control unit that shows NG in that check. First troubleshoot any indicated Network Communications \[CAN gateway\] DTCs using the indicated DTC's troubleshooting. Then use the scanner's Communication Status Check of F-CAN Connected Units. Base the following inspections on which control unit shows NG.

Shared confirmation routine

Here is the separate shared Confirmation Procedure: turn the vehicle to the ON mode. For its details, check the Confirmation Procedure for U0131. This describes the shared routine, rather than adding an initial check before the wiring inspection.

EPS inspection condition

The listed scanner function path is CAN Gateway > Function Test > Communication Status Check of F-CAN Connected Units. If the EPS Control Unit shows NG in Communication Status Check of F-CAN Connected Units, check for open wires in VF-CAN C_H and VF-CAN C_L between the CAN gateway and EPS control unit as follows.

An EPS Control Unit NG result selects this wiring-inspection branch; it is not yet the final diagnosis of an EPS control unit problem. The communication-status result identifies which unit's inspections apply, while the subsequent wiring results distinguish the circuit path from the EPS control unit path.

Wiring inspection setup

For this separate wiring inspection, IG Mode must be OFF. With that condition met, disconnect CAN gateway connector B (24P). Then disconnect EPS control unit connector B (6P). Check the two circuits at the following terminal pairs.

VF-CAN C_H check

For the VF-CAN C_H open-wire check, IG Mode must be OFF. CAN gateway connector B (24P) and EPS control unit connector B (6P) must both be disconnected. Check resistance at the female terminals. Place one probe on CAN gateway connector B terminal 13. Place the other probe on EPS control unit connector B terminal 4. The reading should be less than 1 ohm. That is normal for this circuit check.

VF-CAN C_L check

For the VF-CAN C_L open-wire check, IG Mode must be OFF. CAN gateway connector B (24P) and EPS control unit connector B (6P) must both be disconnected. Check resistance at the female terminals. Place one probe on CAN gateway connector B terminal 1. Place the other probe on EPS control unit connector B terminal 1. The reading should be less than 1 ohm. That is normal for this circuit check.

What the wiring results mean

If these inspection results are abnormal, there is a problem in the circuit. If the results are normal, there is a problem with the EPS control unit.

The normal-results branch depends on both open-wire checks meeting their individual limits, not just one passing reading. Each requires less than 1 ohm; a reading of exactly 1 ohm does not meet that limit. Abnormal inspection results point to the circuit, whereas normal results direct this branch to the EPS control unit.

U0131 troubleshooting prerequisites

For the U0131-specific troubleshooting, first review How to Troubleshoot. Before this troubleshooting, check the EPS control unit power/ground circuit first. Then use the named troubleshooting procedure F-CAN Lost Communication CAN with Bus Connection to Gateway.

U0131 confirmation routine

The separate U0131 Confirmation Procedure is to turn the vehicle to the ON mode and wait 6 seconds.

Scanner function reference

The scanner function listed for reference with U0131 is PGM-FI > Data List.

Final check

U0131 may involve EPS control unit startup, its power/ground circuit, or communication circuitry.

For more guided automotive diagnostics, visit STEP Diagnostics.