DTC guide

U0146 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-CAN Gateway)

U0146 can indicate missing or persistently abnormal CAN gateway information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle Network2025 Honda Accord 1.5 turbo

Quick answer

U0146 can indicate missing or persistently abnormal CAN gateway information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle coverage: 2025 Honda Accord 1.5 turbo. Confirm the exact configuration and applicable safety procedure before testing or repair.

On this page
  1. What this code means
  2. What the vehicle may do
  3. Possible fault areas
  4. Diagnostic path
  5. Understanding U0146
  6. Before troubleshooting
  7. U0146 confirmation routine
  8. Listed scanner function
  9. F-CAN diagnostic prerequisites
  10. Gateway faults take priority
  11. Find the control unit showing NG
  12. Shared confirmation routine
  13. PCM connector safety
  14. Measurement setup
  15. PF-CAN A_H
  16. PF-CAN A_L
  17. PD-CAN B_H
  18. PD-CAN B_L and results
  19. Final check
U0146 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-CAN Gateway) diagnostic guide

What this code means

U0146 can indicate missing or persistently abnormal CAN gateway information reaching the PCM through PF-CAN A or PD-CAN B.

What the vehicle may do

  • The PCM may lose a signal from the CAN gateway.
  • The PCM may receive abnormal information from the CAN gateway.

Possible fault areas

  • The CAN gateway may not start normally.
  • Possible fault areas include control-unit power/ground circuits.
  • Possible fault areas include the PF-CAN A and PD-CAN B circuits.
  • The PCM may also be a fault area.

Diagnostic path

Understanding U0146

On this 2025 Honda Accord 1.5, U0146 points to a PF-CAN A or PD-CAN B communication problem between the Powertrain Control Module (PCM) and CAN gateway. The PCM stores this code if it cannot receive a gateway signal through either line. It also stores the code if gateway information stays abnormal continuously for a specified cycle. Here is what this code tells us. The PCM may lose a signal from the CAN gateway. The PCM may receive abnormal information from the CAN gateway. Here are the main areas to check. The CAN gateway may not start normally. Possible fault areas include control-unit power/ground circuits. Possible fault areas include the PF-CAN A and PD-CAN B circuits. The PCM may also be a fault area.

Before troubleshooting

Before troubleshooting, review How to Troubleshoot. First, check the CAN gateway power/ground circuit. A failure in that circuit can cause this code to be stored. The related diagnostic path is F-CAN Lost Communication CAN with Bus Connection to Gateway.

U0146 describes the communication abnormality detected by the PCM; it does not by itself distinguish a CAN-line fault from a gateway power/ground fault. The gateway power/ground check comes first because a failure there can also cause this DTC to be stored.

U0146 confirmation routine

Here is the separate confirmation routine for U0146. Turn the vehicle to the ON mode, and wait 6 seconds.

Listed scanner function

The diagnostic scanner (HDS) function listing includes PGM-FI > Data List.

F-CAN diagnostic prerequisites

The following checks address lost communication on the F-CAN circuit connected to the CAN gateway. Before starting this troubleshooting, review How to Troubleshoot. If the failure is intermittent or difficult to reproduce, review How to Troubleshoot (Handling Intermittent and Low Reproducibility Failures). Check the power/ground circuit of the transmitting control unit showing NG in the scanner's Communication Status Check of F-CAN Connected Units. For details on using that function, review How to Troubleshoot (Handling Ongoing Failures).

Gateway faults take priority

Troubleshoot any DTCs listed or indicated systems below first. Network Communications \[CAN gateway\]: Go to the indicated DTC's troubleshooting

Troubleshoot any indicated Network Communications \[CAN gateway\] DTCs first. Follow the troubleshooting for the indicated DTC.

Find the control unit showing NG

Use the scanner's Communication Status Check of F-CAN Connected Units. Use the control unit showing NG to determine which inspections follow.

The NG result selects the inspection path; it is not yet the final component diagnosis. In particular, PCM NG leads to the gateway-to-PCM open-wire inspections, whose results distinguish the circuit-problem branch from the PCM-problem branch.

Shared confirmation routine

The shared F-CAN checks also define a separate confirmation routine. Turn the vehicle to the ON mode. For the details that apply to U0146, check its confirmation routine described earlier.

PCM connector safety

The separate open-wire inspection between the CAN gateway and PCM has an important connector precaution. Before disconnecting the PCM connector, jump the SCS line with the scanner. Wait more than 1 minute. The following inspections apply if the PCM shows NG in Communication Status Check of F-CAN Connected Units. The scanner function listing is CAN Gateway > Function Test > Communication Status Check of F-CAN Connected Units.

Measurement setup

For these measurements, CAN gateway connector A (24P) and PCM connector A (72P) must both be disconnected. IG Mode must be OFF. Check the four lines at the following terminal pairs.

PF-CAN A_H

For the PF-CAN A_H open-wire check, keep IG Mode OFF and both specified connectors disconnected. Place one probe on CAN gateway connector A (24P) female terminal 6. Place the other probe on PCM connector A (72P) female terminal 69. The reading should be less than 1 ohm. That is the normal result for this check.

PF-CAN A_L

For the PF-CAN A_L open-wire check, keep IG Mode OFF and both specified connectors disconnected. Place one probe on CAN gateway connector A (24P) female terminal 18. Place the other probe on PCM connector A (72P) female terminal 55. The reading should be less than 1 ohm. That is the normal result for this check.

PD-CAN B_H

For the PD-CAN B_H open-wire check, keep IG Mode OFF and both specified connectors disconnected. Place one probe on CAN gateway connector A (24P) female terminal 23. Place the other probe on PCM connector A (72P) female terminal 72. The reading should be less than 1 ohm. That is the normal result for this check.

PD-CAN B_L and results

For the PD-CAN B_L open-wire check, keep IG Mode OFF and both specified connectors disconnected. Place one probe on CAN gateway connector A (24P) female terminal 11. Place the other probe on PCM connector A (72P) female terminal 71. The reading should be less than 1 ohm. That is the normal result for this check. If the open-wire inspections are abnormal, there is a problem in the circuit. If they are normal, there is a problem with the PCM.

The normal-result decision applies to the full set of four open-wire inspections, not just PD-CAN B_L. Each has a normal limit of less than 1 ohm. Within this PCM-NG path, abnormal inspection results identify a circuit problem; normal results across the set identify a PCM problem.

Final check

When the PCM shows NG, the open-wire inspection results can point to a circuit problem or a PCM problem.

For more guided automotive diagnostics, visit STEP Diagnostics.