DTC guide

U0151 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-SRS Unit)

U0151 can indicate missing or persistently abnormal SRS unit information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle Network2025 Honda Accord 1.5 turbo

Quick answer

U0151 can indicate missing or persistently abnormal SRS unit information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle coverage: 2025 Honda Accord 1.5 turbo. Confirm the exact configuration and applicable safety procedure before testing or repair.

On this page
  1. What this code means
  2. What the vehicle may do
  3. Possible fault areas
  4. Diagnostic path
  5. What U0151 means
  6. Before troubleshooting
  7. U0151 confirmation routine
  8. Listed scanner function
  9. Gateway communication checks
  10. Find the unit marked NG
  11. Shared confirmation routine
  12. Listed gateway function
  13. Before disconnecting the SRS connector
  14. Battery routine conditions
  15. Disconnect the battery terminals
  16. VF-CAN C_H wire check
  17. VF-CAN C_L wire check
  18. More diagnostic steps
  19. Final check
U0151 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-SRS Unit) diagnostic guide

What this code means

U0151 can indicate missing or persistently abnormal SRS unit information reaching the PCM through PF-CAN A or PD-CAN B.

What the vehicle may do

  • The PCM may lose the SRS unit signal.
  • SRS unit information may remain abnormal.

Possible fault areas

  • The SRS unit may not start normally.
  • The SRS unit power/ground circuit may have a fault.
  • The gateway-to-SRS wiring or the SRS unit may have a fault.

Diagnostic path

What U0151 means

On this 2025 Honda Accord 1.5, U0151 names a PF-CAN A, PD-CAN B communication malfunction between the Powertrain Control Module (PCM) and SRS unit. The PCM stores this code if it cannot receive an SRS unit signal through either line, or if SRS unit information remains abnormal continuously for a specified cycle. The code may also be stored if the SRS unit does not start normally or its power/ground circuit fails. Here is what this code tells us. The PCM may lose the SRS unit signal. SRS unit information may remain abnormal. Here are the main areas to check. The SRS unit may not start normally. The SRS unit power/ground circuit may have a fault. The gateway-to-SRS wiring or the SRS unit may have a fault.

Before troubleshooting

Before you troubleshoot, review How to Troubleshoot. Check the SRS unit power/ground circuit first. The shared diagnostic path is F-CAN Lost Communication CAN with Bus Connection to Gateway.

U0151 describes what the PCM detects, not a single failed component. Missing or persistently abnormal SRS information can meet the code conditions, while an SRS startup problem or power/ground circuit failure can also cause the code to be stored. This is why the SRS power/ground check comes before the communication troubleshooting.

U0151 confirmation routine

Here is the separate U0151 Confirmation Procedure. Turn the vehicle to the ON mode. Wait 6 seconds.

Listed scanner function

The diagnostic scanner (HDS) lists this function path: PGM-FI > Data List.

Gateway communication checks

Troubleshoot any DTCs listed or indicated systems below first. Network Communications \[CAN gateway\]: Go to the indicated DTC's troubleshooting

The shared checks address lost communication on the F-CAN circuit connected to the CAN gateway. Before you troubleshoot this path, review How to Troubleshoot. If the failure is intermittent or difficult to reproduce, review How to Troubleshoot (Handling Intermittent and Low Reproducibility Failures). Troubleshoot any indicated Network Communications \[CAN gateway\] DTCs first, using the indicated DTC's troubleshooting.

Find the unit marked NG

For details on using the scanner's Communication Status Check of F-CAN Connected Units, review How to Troubleshoot (Handling Ongoing Failures). Run Communication Status Check of F-CAN Connected Units with the scanner. Look for the control unit whose result is NG. That result determines which inspections apply. Check the power/ground circuit of the transmitting control unit marked NG.

The NG result selects the unit-specific inspection path; it is not itself the final component diagnosis. The shared procedure calls for checking the power/ground circuit of the transmitting control unit marked NG. The gateway-to-SRS wire inspections below apply specifically when the SRS Unit is marked NG in HDS Communication Status Check of F-CAN Connected Units.

Shared confirmation routine

The shared path also defines a separate Confirmation Procedure: turn the vehicle to the ON mode. For the details that apply here, check the U0151 Confirmation Procedure.

Listed gateway function

The scanner also lists this function path: CAN Gateway > Function Test > Communication Status Check of F-CAN Connected Units.

Before disconnecting the SRS connector

Before disconnecting the SRS unit connector, do the 12 volt battery terminal disconnection procedure. Then wait for at least 3 minutes before disconnecting that connector.

Battery routine conditions

Here is the separate 12 volt battery terminal disconnection procedure used for that safety step. On Canada models, the first ON mode after reconnecting the 12 volt battery has a special condition. Depress the brake pedal while turning the vehicle to the ON mode. This is for immobilizer mutual authentication between the body control module and the VSA modulator-control unit. When disconnecting the battery terminals, always disconnect the negative side first. If the 12 volt battery performs abnormally, test the 12 volt battery.

Disconnect the battery terminals

With the driver's door open, turn the vehicle to the OFF (LOCK) mode. Wait at least 3 minutes before disconnecting the 12 volt negative battery cable. Make sure the vehicle is in the OFF (LOCK) mode. Always disconnect the negative side first. To protect the 12 volt battery sensor connector, do not hold it when removing the terminal. Do not disconnect the cable from the 12 volt battery sensor unless you replace the sensor. Disconnect and isolate the 12 volt battery sensor with its cable from the 12 volt battery. Open the positive terminal cover. Disconnect the positive terminal from the 12 volt battery.

The two waits of at least 3 minutes belong to different points in the sequence. With the driver's door open, the first follows selecting OFF (LOCK) and comes before disconnecting the 12 volt negative battery cable. The other follows the battery terminal disconnection procedure and comes before disconnecting the SRS unit connector. Completing the first wait does not replace the second.

VF-CAN C_H wire check

The following wire inspections apply if the SRS Unit shows NG in Communication Status Check of F-CAN Connected Units. Before disconnecting the SRS unit connector, the battery terminal disconnection procedure and the following wait of at least 3 minutes are required. For the VF-CAN C_H open wire inspection, IG Mode must be OFF. CAN gateway connector B (24P) and SRS unit connector A (43P) must both be disconnected. Check resistance between CAN gateway connector B terminal 13 and SRS unit connector A terminal 35. The expected reading is less than 1 Ω.

VF-CAN C_L wire check

For the separate VF-CAN C_L open wire inspection, IG Mode must be OFF. CAN gateway connector B (24P) and SRS unit connector A (43P) must both be disconnected. To check resistance, place one probe on CAN gateway connector B terminal 1. Place the other probe on SRS unit connector A terminal 34. The reading should be less than 1 ohm. If these wire inspection results are abnormal, there is a problem in the circuit. If they are normal, there is a problem with the SRS unit.

These are two separate wire checks, each with a normal reading of less than 1 Ω. A normal C_H result alone does not establish that C_L is normal. In the SRS Unit NG branch, the circuit-versus-SRS-unit conclusion depends on these wire inspection results with IG Mode OFF and both specified connectors disconnected: abnormal results identify a circuit problem, while normal results identify a problem with the SRS unit.

More diagnostic steps

For more diagnostic steps, visit stepdiagnostics.com.

Final check

Communication status, power/ground checks, and gateway-to-SRS wire readings can help identify the documented fault area.

For more guided automotive diagnostics, visit STEP Diagnostics.