DTC guide

U0155 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-Gauge Control Module)

U0155 can indicate missing or persistently abnormal gauge control module information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle Network2025 Honda Accord 1.5 turbo

Quick answer

U0155 can indicate missing or persistently abnormal gauge control module information reaching the PCM through PF-CAN A or PD-CAN B.

Vehicle coverage: 2025 Honda Accord 1.5 turbo. Confirm the exact configuration and applicable safety procedure before testing or repair.

On this page
  1. What this code means
  2. What the vehicle may do
  3. Possible fault areas
  4. Diagnostic path
  5. What U0155 means
  6. Before troubleshooting
  7. The gateway-connected circuit
  8. U0155 confirmation routine
  9. Preparing for the shared F-CAN check
  10. Check gateway codes first
  11. Check communication status
  12. Shared confirmation routine
  13. When the gauge wire checks apply
  14. Check IF-CAN_H
  15. Check IF-CAN_L
  16. More diagnostic steps
  17. Final check
U0155 PF-CAN A, PD-CAN B Malfunction (Powertrain Control Module (PCM)-Gauge Control Module) diagnostic guide

What this code means

U0155 can indicate missing or persistently abnormal gauge control module information reaching the PCM through PF-CAN A or PD-CAN B.

What the vehicle may do

  • The PCM may lose the gauge control module signal.
  • Gauge control module information may remain abnormal.

Possible fault areas

  • The gauge control module may not start normally.
  • The gauge control module power/ground circuit may have a fault.
  • The IF-CAN_H or IF-CAN_L circuit may have a fault.
  • The gauge control module itself may have a fault.

Diagnostic path

What U0155 means

On this 2025 Honda Accord 1.5, U0155 points to a communication problem between the Powertrain Control Module (PCM) and the Gauge Control Module. The PCM can store this code when it cannot receive the gauge control module signal through PF-CAN A or PD-CAN B. It can also store the code when information from the gauge control module stays abnormal continuously for a specified cycle. Here is what this code tells us. The PCM may lose the gauge control module signal. Gauge control module information may remain abnormal. Here are the main areas to check. The gauge control module may not start normally. The gauge control module power/ground circuit may have a fault. The IF-CAN_H or IF-CAN_L circuit may have a fault. The gauge control module itself may have a fault.

Before troubleshooting

Before you troubleshoot, review How to Troubleshoot. Check the power/ground circuit of the gauge control module first. A failure in that circuit can cause U0155 to be stored.

U0155 describes what the PCM detects, not which component has failed. Because a gauge control module power/ground circuit failure can also store this code, that prerequisite check matters before interpreting the later wire checks as evidence of a module problem.

The gateway-connected circuit

For this code, use the F-CAN Lost Communication CAN with Bus Connection to Gateway troubleshooting.

U0155 confirmation routine

The separate U0155 Confirmation Procedure is defined as follows. Turn the vehicle to the ON mode. Then wait 6 seconds.

Preparing for the shared F-CAN check

The diagnostic scanner (HDS) has a listed function reference: PGM-FI > Data List. The shared troubleshooting covers lost communication in the F-CAN circuit connected to the CAN gateway. Before you troubleshoot this circuit, review How to Troubleshoot. If the failure happens intermittently or is difficult to reproduce, review How to Troubleshoot (Handling Intermittent and Low Reproducibility Failures). A transmitting control unit that indicates NG in Communication Status Check of F-CAN Connected Units requires a power/ground circuit check.

Check gateway codes first

Troubleshoot any DTCs listed or indicated systems below first. Network Communications \[CAN gateway\]: Go to the indicated DTC's troubleshooting

If Network Communications \[CAN gateway\] indicates a DTC, troubleshoot that indicated DTC first.

Check communication status

For details on using the scanner's Communication Status Check of F-CAN Connected Units, review How to Troubleshoot (Handling Ongoing Failures). Then run Communication Status Check of F-CAN Connected Units with the scanner. Use the control unit whose result is NG to determine which inspections apply.

The NG result selects the inspection path; it is not, by itself, a diagnosis of a failed control unit. The shared procedure requires a power/ground circuit check for the transmitting unit that indicates NG. The gauge-specific IF-CAN wire inspections apply when the Gauge Control Module is the unit indicating NG.

Shared confirmation routine

The shared F-CAN troubleshooting also defines a separate Confirmation Procedure. That routine calls for turning the vehicle to the ON mode. For its details, check the Confirmation Procedure for the DTC being diagnosed, U0155.

When the gauge wire checks apply

Another listed scanner function reference is CAN Gateway > Function Test > Communication Status Check of F-CAN Connected Units. These wire checks apply if the Gauge Control Module indicates NG in Communication Status Check of F-CAN Connected Units.

Check IF-CAN_H

For these wire checks, IG Mode must be OFF. CAN gateway connector A (24P) and Gauge control module connector A (32P) must both be disconnected. Let us check the two specified wire paths, starting with IF-CAN_H. Use the female terminals for this measurement. Place one probe on CAN gateway connector A (24P) terminal 17. Place the other probe on Gauge control module connector A (32P) terminal 18. The reading should be less than 1 ohm. That is the normal result for this IF-CAN_H open wire inspection.

Check IF-CAN_L

For the IF-CAN_L check, IG Mode must be OFF, with both connectors disconnected. Use the female terminals for this measurement. Place one probe on CAN gateway connector A (24P) terminal 5. Place the other probe on Gauge control module connector A (32P) terminal 19. The reading should be less than 1 ohm. That is the normal result for this IF-CAN_L open wire inspection. If these wire checks are abnormal, there is a problem in the circuit. If they are normal, there is a problem with the gauge control module.

The normal branch depends on both specified wire paths, not just one passing reading. Each must measure less than 1 ohm with IG Mode OFF, both connectors disconnected, and the measurements made at the specified female terminals. Within the Gauge Control Module NG branch, abnormal wire-check results identify a circuit problem; normal results identify a gauge control module problem.

More diagnostic steps

For more diagnostic steps, visit stepdiagnostics.com.

Final check

The documented checks can separate an IF-CAN circuit problem from a gauge control module problem when the module indicates NG.

For more guided automotive diagnostics, visit STEP Diagnostics.