DTC guide

U1288 Gauge control module lost communication with PARKSR

U1288 can indicate that the gauge control module is not receiving specified data from the parking and back-up sensor control unit.

Vehicle Network2025 Honda Accord 1.5 turbo

Quick answer

U1288 can indicate that the gauge control module is not receiving specified data from the parking and back-up sensor control unit.

Vehicle coverage: 2025 Honda Accord 1.5 turbo. Confirm the exact configuration and applicable safety procedure before testing or repair.

On this page
  1. What this code means
  2. What the vehicle may do
  3. Possible fault areas
  4. Diagnostic path
  5. What U1288 means
  6. Before troubleshooting
  7. U1288 confirmation
  8. Scanner function reference
  9. Gateway-connected communication checks
  10. Check communication status
  11. F-CAN confirmation
  12. Gateway scanner function
  13. Prepare for the open-wire checks
  14. Check AF-CAN B_H
  15. Check AF-CAN_B L
  16. What the results mean
  17. More diagnostic steps
  18. Final check
U1288 Gauge control module lost communication with PARKSR diagnostic guide

What this code means

U1288 can indicate that the gauge control module is not receiving specified data from the parking and back-up sensor control unit.

The gauge control module is reporting missing data, not identifying the failed part. The parking and back-up sensor control unit may fail to start normally, and a fault in its power/ground circuit can also cause this code to be stored. This is why the power/ground check comes before the communication-circuit troubleshooting.

What the vehicle may do

  • The gauge control module may not receive the specified data.

Possible fault areas

  • The parking and back-up sensor control unit may not start normally.
  • Its power/ground circuit may have a fault.
  • The AF-CAN wiring or the sensor control unit may have a fault.

Diagnostic path

What U1288 means

On this 2025 Honda Accord 1.5, U1288 means the gauge control module has lost communication with PARKSR, the parking and back-up sensor control unit. The gauge control module stores this code when it cannot receive the specified data from that unit. Possible fault areas include the unit starting incorrectly, its power/ground circuit, and the communication wiring. Here is what this code tells us. The gauge control module may not receive the specified data. Here are the main areas to check. The parking and back-up sensor control unit may not start normally. Its power/ground circuit may have a fault. The AF-CAN wiring or the sensor control unit may have a fault.

Before troubleshooting

Before you troubleshoot, review How to Troubleshoot. If you are troubleshooting multiple DTCs, follow B-CAN System Diagnosis Test Mode A. A power/ground circuit failure in the sensor control unit can also store U1288. Before this troubleshooting, check the power/ground circuit of the parking and back-up sensor control unit first. Then use the troubleshooting for F-CAN Lost Communication (CAN BUS with Connection to CAN Gateway).

U1288 confirmation

The separate U1288 Confirmation Procedure calls for turning the vehicle to the ON mode.

Scanner function reference

A listed function for the diagnostic scanner (HDS) is Body Electrical > Gauges > Data List. This is a function reference, not a selection step in the confirmation procedure.

Gateway-connected communication checks

The F-CAN Lost Communication troubleshooting covers a communication failure in the F-CAN circuit connected to the CAN gateway. Before you troubleshoot that circuit, review How to Troubleshoot. If the failure is intermittent or difficult to reproduce, review How to Troubleshoot (Handling Intermittent and Low Reproducibility Failures). Check the power/ground circuit of the transmitting control unit showing NG in the scanner's Communication Status Check of F-CAN Connected Units.

Check communication status

Troubleshoot any DTCs listed or indicated systems below first. Network Communications \[CAN gateway\]: Go to the indicated DTC's troubleshooting

If Network Communications \[CAN gateway\] DTCs are indicated, troubleshoot those DTCs first. For details on using Communication Status Check of F-CAN Connected Units, review How to Troubleshoot (Handling Ongoing Failures). Then use the scanner to run Communication Status Check of F-CAN Connected Units. Base the following inspections on the control unit whose result is NG.

The NG result selects which control unit's inspection path applies. For the parking and back-up sensor control unit, it leads to the open-wire inspections below; NG alone is not the final diagnosis of a faulty unit. The circuit inspection results distinguish the circuit-fault path from the control-unit-fault path.

F-CAN confirmation

The separate F-CAN Confirmation Procedure also calls for turning the vehicle to the ON mode. For its details, check the U1288 Confirmation Procedure.

Gateway scanner function

Another listed scanner function is CAN Gateway > Function Test > Communication Status Check of F-CAN Connected Units.

Prepare for the open-wire checks

If the Parking and Back-up Sensor Control Unit shows NG in Communication Status Check of F-CAN Connected Units, carry out these separate open-wire checks. Keep IG Mode OFF for these checks. Disconnect CAN gateway connector B (24P). Also disconnect Parking and back-up sensor control unit connector (24P). With IG Mode OFF and both connectors disconnected, check the two circuits at the following terminals.

Check AF-CAN B_H

To check AF-CAN B_H for an open wire, keep IG Mode OFF and both connectors disconnected. Place one probe on CAN gateway connector B (24P) female terminal 15. Place the other probe on Parking and back-up sensor control unit connector (24P) female terminal 13. Check the resistance between these terminals. The reading should be less than 1 ohm. That is the normal result for this circuit.

Check AF-CAN_B L

To check AF-CAN_B L for an open wire, keep IG Mode OFF and both connectors disconnected. Place one probe on CAN gateway connector B (24P) female terminal 3. Place the other probe on Parking and back-up sensor control unit connector (24P) female terminal 2. Check the resistance between these terminals. The reading should be less than 1 ohm. That is the normal result for this circuit.

What the results mean

If the inspection results are abnormal, there is a problem in the circuit. If the inspection results are normal, there is a problem with the parking and back-up sensor control unit.

The normal-results branch requires both listed open-wire inspections to be normal, not just one. Each requires less than 1 Ω with IG Mode OFF and both specified connectors disconnected; exactly 1 Ω does not meet that limit. The control-unit diagnosis belongs to this NG-selected inspection path after the prerequisite power/ground check, rather than following from U1288 alone.

More diagnostic steps

For more diagnostic steps, visit stepdiagnostics.com.

Final check

Power/ground faults, AF-CAN circuit faults, or a parking and back-up sensor control unit problem can be involved.

For more guided automotive diagnostics, visit STEP Diagnostics.