What this code means
P2421 can indicate too little pressure change after the EVAP canister vent shut valve is commanded closed during purging.
What the vehicle may do
- The pressure-change response can be too low during purging.
Possible fault areas
- Possible faults include the vent hose, purge valve, and purge-line parts.
- The vent shut valve, fuel fill pipe, and vapor recirculation tube may be involved.
- The main flap unit or fuel tank may also be involved.
Diagnostic path
What P2421 means
On this 2025 Honda Accord 1.5, P2421 means Evaporative Emission (EVAP) Canister Vent Shut Valve Stuck Open. We will call it the vent shut valve. Here is what this code tells us. During EVAP system purging, the PCM commands this valve closed. If the FTP sensor pressure-change value is below the specified value afterward, the PCM stores this code. The pressure-change response can be too low during purging. Here are the main areas to check. Possible faults include the vent hose, purge valve, and purge-line parts. The vent shut valve, fuel fill pipe, and vapor recirculation tube may be involved. The main flap unit or fuel tank may also be involved.
The code records an insufficient FTP sensor pressure change after a close command, rather than a direct observation of the valve’s position. This is why the inspection path covers several EVAP components instead of identifying the vent shut valve from the code name alone.
Before troubleshooting
Before you troubleshoot, review How to Troubleshoot.
Tools and pressure precautions
Use a Vacuum Pump/Gauge, 0-30 inHg, Snap-on YA4000B or equivalent, commercially available. The fuel system is designed for specified maximum vacuum and pressure conditions. Do not deviate from the pressure and vacuum tests described here. Excessive pressure or vacuum would damage EVAP components or cause eventual fuel tank failure. Fresh fuel has higher volatility and creates greater pressure and vacuum. The best testing condition is less than a full tank of fresh fuel. If possible, add 1 gallon of fresh fuel just before starting these procedures to help with leak detection. Do this only if it will not fill the tank. In the inspection illustration, a dotted line marks the components to be tested. That illustration does not show every area that needs inspection.
Confirmation check
The separate confirmation check works like this. Turn the vehicle to the ON mode. Use the diagnostic scanner (HDS) to do \[FUNCTION TEST\]. If the result is not OK, the failure is duplicated.
Scanner function reference
The scanner function reference lists these paths: PGM-FI > Function Test > EVAP TEST > FUNCTION TEST. PGM-FI > Function Test > EVAP TEST > SINGLE SOLENOID > PCS(CPV) ON. PGM-FI > Function Test > EVAP TEST > SINGLE SOLENOID > CVS ON. It also lists PGM-FI > Data List, with the signal FTP Sensor Voltage.
Vent hose check
For the vent hose check, the EVAP canister vent hose must be disconnected. Check the hose for blockage or restriction. There should be no blockage or restriction. If you find either, there is a problem with the vent hose.
Purge valve open-stuck check
For the EVAP canister purge valve inspections, the valve must be removed with its connector still connected. Use the vacuum pump/gauge, 0-30 inHg, to apply pressure or vacuum as specified for each check. For the separate open-stuck check, apply pressure to the one-side port shown for this check. Pressure should be held. If it is not held, there is a problem with the purge valve.
Purge valve close-stuck check
For the separate EVAP Canister Purge Valve Close Stuck Inspection, select \[PCS(CPV) ON\] on the scanner. Apply pressure to the one-side port shown for this check. Pressure should not be held. If pressure is held, there is a problem with the purge valve.
These two pressure checks have opposite specifications. With the purge valve removed and its connector connected, the open-stuck check requires pressure to hold at its shown port. The close-stuck check uses HDS [PCS(CPV) ON] and requires pressure not to hold at its shown port. Holding pressure is therefore not a general pass result; its meaning depends on which inspection is being performed.
Purge valve leak and non-return check
The EVAP Canister Purge Valve Leak and Non-Return Valve Open Stuck inspection is required for this troubleshooting. Before doing it, do the EVAP Canister Purge Valve Close Stuck Inspection. Confirm that its result is within specification: pressure is not held. For the leak and non-return valve open-stuck check, select \[PCS(CPV) ON\] on the scanner. Apply vacuum to the one-side port shown for this check. Vacuum should be held. If vacuum is not held, there is a problem with the purge valve.
Non-return valve A check
This separate check is for Non-Return Valve A Close Stuck, on the intake manifold side. Select \[PCS(CPV) ON\] on the scanner. Apply vacuum to the one-side port shown for valve A. Vacuum should not be held. If vacuum is held, there is a problem with the purge valve.
Non-return valve B check
This separate check is for Non-Return Valve B Close Stuck, on the turbocharger side. Select \[PCS(CPV) ON\] on the scanner. Apply vacuum to the one-side port shown for valve B. Vacuum should not be held. If vacuum is held, there is a problem with the purge valve.
Although these vacuum inspections all use HDS [PCS(CPV) ON], they do not share one expected result. The leak and non-return valve open-stuck inspection requires vacuum to hold, after the close-stuck inspection passes. The separate valve A intake-manifold-side and valve B turbocharger-side checks require vacuum not to hold at their respective shown ports. A result from one check cannot be interpreted using another check’s specification.
Purge-line visual check
For the separate visual check, look along the EVAP canister purge line between the purge valve and canister. Check for poor connections or damage. Also check the EVAP canister, FTP sensor, vent shut valve, and O-rings for damage. The connections should be OK, and there should be no damage. If this check is abnormal, there is a problem with the parts on the purge line.
Purge-line vacuum check
For the separate purge-line vacuum check, disconnect the EVAP canister vent hose and fuel vent tube from the canister. Plug each disconnected canister port as shown. Disconnect the vacuum hose, or purge line, from the purge valve in the engine compartment. Connect the vacuum pump/gauge, 0-30 inHg, to that vacuum hose as shown. Turn the vehicle to the ON mode. Be careful not to exceed the specified vacuum. Excess vacuum can damage the FTP sensor. Apply vacuum to the hose until the scanner \[FTP Sensor Voltage\] reads 1.90 V (-0.59 inHg, -15.1 mmHg). Monitor \[FTP Sensor Voltage\] for 1 minute. The reading should not increase more than 0.2 V (0.1 inHg, 2.5 mmHg). That is the normal result. If the result is abnormal, there is a problem with the parts on the purge line.
Reaching 1.90 V (-0.59 inHg, -15.1 mmHg) establishes the starting condition; it does not by itself complete the check. The result depends on the change during the following 1 minute. An increase of no more than 0.2 V (0.1 inHg, 2.5 mmHg) meets the specification, while a greater increase points to the purge-line parts, not to one individually identified component.
Vent shut valve vacuum check
For the separate vent shut valve check, the EVAP canister purge line must be normal. Disconnect the fuel vent tube from the EVAP canister, and plug that canister port as shown. Disconnect the vacuum hose, or purge line, from the purge valve in the engine compartment. Connect the vacuum pump/gauge, 0-30 inHg, to that vacuum hose as shown. Turn the vehicle to the ON mode. Select \[CVS ON\] on the scanner. Be careful not to exceed the specified vacuum. Excess vacuum can damage the FTP sensor. Apply vacuum to the hose until the scanner \[FTP Sensor Voltage\] reads 1.90 V (-0.59 inHg, -15.1 mmHg). Monitor \[FTP Sensor Voltage\] for 1 minute. The reading should not increase more than 0.2 V (0.1 inHg, 2.5 mmHg). That is the normal result. If the result is abnormal, there is a problem with the vent shut valve.
The normal purge-line prerequisite is what allows an abnormal result here to be assigned to the vent shut valve. This is a distinct setup: the purge-line check plugs both disconnected canister ports, whereas this check plugs the fuel vent tube port and uses HDS [CVS ON]. The two setups should not be treated as interchangeable.
Fuel fill pipe and vapor tube
For this separate visual check, check the fuel fill pipe and fuel tank vapor recirculation tube. Look for poor connections or damage. The connections should be OK, and there should be no damage. If this check is abnormal, there is a problem with the fuel fill pipe, vapor recirculation tube, or both.
Main flap unit check
For the separate main flap unit check, check that the shut-off valve is closed. Inspect its flap seal and mating surface for missing material or damage. The shut-off valve should be closed, with no missing or damaged seals. If the check is abnormal, there is a problem with the main flap unit.
Fuel tank conclusion
The fuel tank conclusion depends on the other inspection results. If all the other inspection items are normal, the remaining fuel tank is determined to be the cause.
Final check
The fuel tank may be identified as the cause only when all other inspection items indicate normal conditions.
For more guided automotive diagnostics, visit STEP Diagnostics.






